メインコンテンツへスキップ

スイッチ側のSFPの障害が原因でFCPターゲットアダプタのリンクが切断されたことを示しています

Views:
133
Visibility:
Public
Votes:
0
Category:
ontap-9
Specialty:
SAN
Last Updated:

環境

  • ONTAP 9
  • FCP
  • BrocadeおよびCisco SANスイッチ

問題

  • イベントログのエントリは、FCリンクが切断されたことを示しています。

5/23/2020 21:11:31  cluster-node1  ERROR scsitarget.ispfct.linkBreak: Link break detected on Fibre Channel target adapter 1b. Firmware status code status1 0x2, status2 0x7, and status4 0x0.

  • sysconfg -a ポートのステータスをLink Disconnected 」と報告します。

slot 1: Fibre Channel Target Host Adapter 1b
         (QLogic 8324 (8362) rev. 2, <LINK DISCONNECTED>)
         Board Name:     QLE2672
         Serial Number:    RFE2005W04482
         Firmware rev:    8.9.0
         Flash rev:      1.1.2
         Host Port Addr:   000000
         FC Nodename:     xx:0a:09:80:80:xx:xy:xx (500a098080b3a125)
         FC Portname:     xx:0a:09:82:80:xy:yy:xx (500a098280b3a125)
         Connection:     No link
         Switch Port:     Unknown
  SFP Vendor Name:   FINISAR CORP.
  SFP Vendor P/N:   FTLF8529P4BCV-QM
  SFP Vendor Rev:   B
  SFP Serial No.:   P2SABCS
  SFP Connector:    LC

  • RxおよびTx電源が 、 FCP-Adapter.xmlASUPでファイバチャネルターゲットアダプタの ログに対して0.0 (uWatts) と表示される。

Rx : 0.0 (uWatts)
Tx : 0.0 (uWatts)

  • RxおよびTx電力は、ストレージ側とスイッチ側の両方で最適です。

port 9a
Rx : 623.0 (uWatts)
Tx : 1020.9 (uWatts)

Slot  9/Port  2:
RX Power:   -0.5   dBm (883.9uW) 
TX Power:   -1.6   dBm (697.3 uW) 

 

  • Network fcp adapter show CLIで実行したコマンドで動作ステータスが「link disconnected」と報告される

cluster::> network fcp adapter show
           Connection  Port    Admin   Operational
Node      Adapter Established Address   Status  Status
------------ ------- ----------- --------- ------- -----------------------
cluster-node1
       0c    false     0      up    link not connected
cluster-node1
       0d    false     0      up    link not connected
cluster-node1
       1a      true     f0500    up    online
cluster-node1
       1b    true     0      up    link disconnected
cluster-node2
       0c    false     0      up    link not connected
cluster-node2
       0d    false     0      up    link not connected
cluster-node2
       1a    true     f0600    up      online
cluster-node2
       1b    true     f0600    up    online

  • ストレージHBAポートはまだ物理的に接続されている
  • 以下のトラブルシューティング手順を確認して、問題を特定できます。
    1. 次のコマンドを使用して、リモートSFPヘルスを確認し、ポートをバウンスします。

シスコの例:

switch# config terminal
switch(config)# interface fc <slot>/<port#>
switch(config)# show int fc <slot>/<port#> transceiver detail
switch(config-if)# shutdown
switch(config-if)# no shutdown

Brocadeの例:

switch:admin> sfpshow <index # OR slot/port #>
switch:admin> portdisable <index # OR slot/port #>
switch:admin> portenable <index # OR slot/port #>

  1. 物理的な点検を実施し、リンクおよび パッチパネルコンポーネントを取り付け直す。
  2. 再装着後にポートバウンスプロセスを繰り返します。
  3. ケーブルやSFPなどのコンポーネントの両端を交換/交換します。

 

 

Sign in to view the entire content of this KB article.

New to NetApp?

Learn more about our award-winning Support

NetApp provides no representations or warranties regarding the accuracy or reliability or serviceability of any information or recommendations provided in this publication or with respect to any results that may be obtained by the use of the information or observance of any recommendations provided herein. The information in this document is distributed AS IS and the use of this information or the implementation of any recommendations or techniques herein is a customer's responsibility and depends on the customer's ability to evaluate and integrate them into the customer's operational environment. This document and the information contained herein may be used solely in connection with the NetApp products discussed in this document.