CiscoクラスタスイッチのISLポートが停止している

最後の更新
PDFとして保存

Views:: 11

Visibility:: Public

Votes:: 0

Category:: ontap-9

Specialty:: hw<a>2009627569</a>

Last Updated:

環境

ONTAP 9
N9K-C9336C-FX2

問題

新しいCiscoクラスタスイッチのセットアップ後、ISLポートがdownと表示される。
スイッチ1

`show interface brief` -------------------------------------------------------------------------------- Ethernet VLAN Type Mode Status Reason Speed Port Interface Ch # -------------------------------------------------------------------------------- Eth1/35 1 eth trunk down Link not connected auto(D) 1 Eth1/36 1 eth trunk down Link not connected auto(D) 1

スイッチ2

`show interface brief` -------------------------------------------------------------------------------- Ethernet VLAN Type Mode Status Reason Speed Port Interface Ch # -------------------------------------------------------------------------------- Eth1/35 1 eth trunk down Link not connected auto(D) 1 Eth1/36 1 eth trunk down Link not connected auto(D) 1
両方のスイッチのインターフェイスの1つに「transceiver is not supported」と表示されます。
スイッチ1

Ethernet1/35    transceiver is not supported

    Calibration info not available

    Calibration info not available

    Calibration info not available

    Calibration info not available

    Calibration info not available

    Calibration info not available

    Calibration info not available

    Calibration info not available

    Calibration info not available

    Calibration info not available

    Calibration info not available

    Calibration info not available

    Calibration info not available

    Calibration info not available

    Calibration info not available

    Calibration info not available

    Calibration info not available

Ethernet1/36     transceiver is present     type is QSFP-100G-PCC     name is Molex     part number is 112-00574     revision is B0     serial number is 93A2232621382     nominal bitrate is 25500 MBit/sec     Link length supported for copper is 2 m     cisco id is 17     cisco extended id number is 0

DOM is not supported

スイッチ2

`show interface transceiver detail`

Ethernet1/35    transceiver is not supported

    Calibration info not available

    Calibration info not available

    Calibration info not available

    Calibration info not available

    Calibration info not available

    Calibration info not available

    Calibration info not available

    Calibration info not available

    Calibration info not available

    Calibration info not available

    Calibration info not available

    Calibration info not available

    Calibration info not available

    Calibration info not available

    Calibration info not available

    Calibration info not available

    Calibration info not available

Ethernet1/36     transceiver is present     type is QSFP-40G-CR4     name is CISCO-JPC     part number is P3007U101000-1     revision is A0     serial number is JPC25090339-A     nominal bitrate is 10300 MBit/sec per channel     Link length supported for copper is 1 m     cisco id is 13     cisco extended id number is 16     cisco part number is 37-1322-03     cisco product id is QSFP-H40G-CU1M     cisco version id is V03

DOM is not supported
以下のイベントは、show loggingに表示されます。

`show logging log` SW1 %ETHPORT-3-IF_UNSUPPORTED_TRANSCEIVER: Transceiver on interface Ethernet1/35 is not supported SW2 %ETHPORT-3-IF_UNSUPPORTED_TRANSCEIVER: Transceiver on interface Ethernet1/35 is not supported
使用するケーブルは、Hardware Universeに従ってサポートされています。