メインコンテンツまでスキップ

クラスタからATTOブリッジのIPアドレスの変更が失敗します

Views:
6
Visibility:
Public
Votes:
0
Category:
metrocluster
Specialty:
metrocluster<a>2009500006</a>
Last Updated:

環境

  • ONTAP 9
  • FAS / AFFシステム
  • ファブリック接続MetroCluster
  • インバンド 監視中のATTOブリッジ

問題

  • IPアドレスの変更後にATTOブリッジでエラーステータスが報告されます。

Cluster1::> storage bridge show -fields name,status
name          status
--------------------- ------
ATTO_2000XXXXXXXXXX40 error
ATTO_2000XXXXXXXXXX80 error
ATTO_2000XXXXXXXXXX90 error
ATTO_2000XXXXXXXXXXc0 error
4 entries were displayed.

  • ノードからブリッジ到達不能アラートが報告されます。

Cluster1::> system health alert show
        Node: Node-n3
      Alert ID: StorageBridgeUnreachable_Alert
      Resource: ATTO_200000108XXXXX40
      Severity: Major
   Indication Time: Wed Mar 15 19:21:32 2023
      Suppress: false
     Acknowledge: false
   Probable Cause: "ATTO_200000XXXXXXXX40" bridge is not reachable over
           management network.
   Possible Effect: Bridge "ATTO_200000XXXXXXXX40" cannot be monitored for
           alerts.
 Corrective Actions: 1) If the bridge is monitored by SNMP, verify that the node management LIF is up
           by using the "network interface show" command. Verify that the "ATTO_200000XXXXXXXX40"
           bridge is alive by using the "network ping" command.
           2) If the bridge is monitored in-band, check the fabric cabling to the bridge,
           and then verify that the bridge is powered up.

  • 次の場合、ブリッジ監視の変更が失敗します。

1.新しいIPアドレスを追加しようとしています。

Cluster1::> system bridge add -name ATTO_172.20.YY.YY -address 172.20.YY.YY -managed-by in-band
 
Error: command failed: Internal error. Failed to add bridge for monitoring on node "Node-n3" in cluster "Cluster1". Reason: Bridge ATTO_172.20.YY.YY not found in array_profile_db.

2.既存のIPアドレスを変更しようとしています。

Cluster1::> storage bridge modify -name ATTO_200000XXXXXXXXc0 -address 172.20.YY.YY

Error: command failed: Bridge is not reachable over SNMP on node "Node-n3" in cluster "Cluster1". Verify that the node management LIF is up by using the "network interface show -role node_mgmt" command on a node in cluster "Cluster1". Verify that SNMP is enabled on the bridge using a method supplied by the bridge's vendor (ATTO). Then try the command again.

3. ヘルスモニタリングからブリッジを削除および再追加します。

Cluster1::> storage bridge remove -name ATTO_200000XXXXXXXXc0

Cluster1::> storage bridge add -name ATTO_200000XXXXXXXXc0 -address 172.20.YY.YY -managed-by in-band

Cluster1::> storage bridge show -name ATTO_200000XXXXXXXXc0 -fields address
name          address    
--------------------- ------------
ATTO_200000XXXXXXXXc0 172.19.XX.XX

Sign in to view the entire content of this KB article.

New to NetApp?

Learn more about our award-winning Support

NetApp provides no representations or warranties regarding the accuracy or reliability or serviceability of any information or recommendations provided in this publication or with respect to any results that may be obtained by the use of the information or observance of any recommendations provided herein. The information in this document is distributed AS IS and the use of this information or the implementation of any recommendations or techniques herein is a customer's responsibility and depends on the customer's ability to evaluate and integrate them into the customer's operational environment. This document and the information contained herein may be used solely in connection with the NetApp products discussed in this document.