ブート中にパニックが発生し、コアダンプが作成されませんでした

最後の更新
PDFとして保存

Views:: 53

Visibility:: Public

Votes:: 0

Category:: ontap-9

Specialty:: core<a>2008997310.</a>

Last Updated:

環境

ONTAP 9.8p6
AFF A700

問題

ONTAP 9.8p6 へのアップグレード中に、ブートプロセスでシステムパニックが発生しましたが、コアファイルが生成されませんでした。

Please choose one of the following:

(1) Normal Boot.

(2) Boot without /etc/rc.

(3) Change password.

(4) Clean configuration and initialize all disks.

(5) Maintenance mode boot.

(6) Update flash from backup config.

(7) Install new software first.

(8) Reboot node.

(9) Configure Advanced Drive Partitioning.

(10) Set Onboard Key Manager recovery secrets.

(11) Configure node for external key management.

Selection (1-11)? 1

Pensando Offload Driver, ver 1.4.0-E-78

Pensando Ethernet NIC Driver, ver: 1.4.0-E-96

ionic_rdma ver 1.4.0-E-96 : Pensando RoCE HCA driver

e1a: mlx5e_set_board_type port_name = e1a port_psid = NAP0000002006, device_id = 0x1017, vendor_id = 0x15b3

e1b: mlx5e_set_board_type port_name = e1b port_psid = NAP0000002006, device_id = 0x1017, vendor_id = 0x15b3

e10a: mlx5e_set_board_type port_name = e10a port_psid = NAP0000002006, device_id = 0x1017, vendor_id = 0x15b3

e10b: mlx5e_set_board_type port_name = e10b port_psid = NAP0000002006, device_id = 0x1017, vendor_id = 0x15b3

Dec 01 22:00:54 [FSA700-4B:discover.6500.unsupported:notice]: FC-to-SAS bridge ATTO 6500N discovery is disabled.

PANIC : page fault (supervisor read data, page not present) on VA 0x88 cs:rip 0x20:0xffffffff806ce644 rflags 0x10246

version: 9.8P6: Tue Aug 3 12:23:18 EDT 2021

conf : x86_64.optimize

cpuid = 1

KDB: stack backtrace:

vpanic() at vpanic+0x70d/frame 0xfffff700000071f0

panic() at panic+0x43/frame 0xfffff70000007250

amd64_syscall() at amd64_syscall+0x116e/frame 0xfffff700000072c0

trap() at trap+0xb95/frame 0xfffff70000007330

trap() at trap+0x1c0/frame 0xfffff70000007440

calltrap() at calltrap+0x8/frame 0xfffff70000007440

--- trap 0xc, rip = 0xffffffff806ce644, rsp = 0xfffff70000007510, rbp = 0xfffff70000007510 ---

device_get_softc() at device_get_softc+0x4/frame 0xfffff70000007510

qla_sysconfig_detail() at qla_sysconfig_detail+0x11e/frame 0xfffff70000007620

qla_get_config() at qla_get_config+0x34/frame 0xfffff70000007650

kmod_pci_info_nic() at kmod_pci_info_nic+0xd5/frame 0xfffff700000076a0

kern_ethernet_controller_info_init() at kern_ethernet_controller_info_init+0x133/frame 0xfffff70000009870

sysinit_thread() at sysinit_thread+0x1ab/frame 0xfffff70000009a60

fork_exit() at fork_exit+0xc7/frame 0xfffff70000009ab0

fork_trampoline_sk() at fork_trampoline_sk+0xe/frame 0xfffff70000009ab0

--- trap 0, rip = 0, rsp = 0, rbp = 0 ---

Uptime: 3m7s

ahcich0: AHCI reset done: devices=00000001

Dumper is not yet registered. A coredump will not be available at this time.

System halting...

BIOS Version: 10.11